ASTM A ASME SA “Standard Specification for Nickel and Nickel-Base Alloy-Clad Steel. Plate”. “STANDARD SPECIFICATION FOR NICKEL AND. Buy ASTM A SPECIFICATION FOR NICKEL AND NICKEL-BASE ALLOY-CLAD STEEL PLATE from SAI Global. Designation: A − 12Standard Specification for Nickel and Nickel-Base Alloy- Clad Steel Plate1 This standard is issued unde.
|Published (Last):||26 December 2004|
|PDF File Size:||12.56 Mb|
|ePub File Size:||14.63 Mb|
|Price:||Free* [*Free Regsitration Required]|
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every? Materials and Manufacture 5. For purposes of de? Repair of Cladding by Welding If spectrometric procedures are used, the sample shall be exposed on the center line of the cladding when there is sufficient cladding thickness available so that there is no contamination from the adjacent base metal.
The minimum cladding thickness for shear testing shall be 0. Number of Tests and Retests 8. In reducing the thickness of the specimen, both the alloy 3 Metric Equivalents in. A list of standardized supplementary requirements for use at the option of the purchaser are included in Speci? It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.
The material is generally intended for pressure vessel use but may be used in other structural applications where corrosion resistance of the alloy is of prime importance.
Each specimen shall be in the? Current edition approved May 1, Historical Version s – view previous versions of standard Translated Version s: These bend tests shall be made in the manner of the tension tests indicated in Fig.
Ultrasonic Examination in accordance with Speci?
Chemical analysis may be accomplished by wet chemical or instrumental procedures. When none has been speci? The nickel q265 nickel-base alloy cladding metal shall conform to prescribed chemical composition. The reduced section shall have a gradual taper from the ends toward the center, with the ends 0.
The base metal shall be carbon steel or low-alloy steel conforming to the specifications for steels for either pressure vessels or for general structural applications.
If wet chemical procedures are used, millings may be taken only when the composite plate thickness is sufficient to permit obtaining millings without danger of contamination from the adjacent layer. Areas within 1 in. All other tensile test wstm of the speci? The sides of the bend asym specimen used for bond strength determination may have the corners rounded to a radius not over 1? Individual reprints single or multiple copies of this standard may be obtained by contacting ASTM at the above address or at phonefaxor service astm.
ASTM A265 GR 1 titanium alloy strip sheet plate
This specification covers the standard for plate of a carbon steel or low-alloy steel base to which is integrally and continuously bonded on one or both sides a layer of nickel or nickel-base alloy.
Reports shall include the results of ultrasonic inspection when Supplementary Requirement S12 is speci? Several of those considered suitable for use with this speci? Greater separation shall be cause for rejection. Testing for shear strength for clad plates with minimum cladding zstm of 0. Permissible Variations Metric Equivalents in.
Such requirements may include, but are ast limited to the following: Originally a65 in ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
ASTM A265 Clad Plate
If you feel that your comments have not received a fair hearing you should make your views known to the ASTM Committee on Standards, at the address shown below. Product and chemical analyses shall be performed on the cladding alloy and be accomplished by wet chemical or instrumental procedures. The composite plate shall undergo shear strength test, bond strength test, and tension test and shall conform to the required tensile strength and yield strength.
Workmanship Finish, and Appearance Approved May 1, Last previous edition approved in as A — The surface condition of the repaired area shall be restored to a condition similar to the rest of the cladding. Your comments will receive careful consideration at a meeting of the responsible technical committee, which you may attend.
Method of test and acceptance standard shall be as agreed upon between the purchaser and the manufacturer.
ASTM A Clad Plate | ASTM A Plate | ASTM A Nickel Coated Plate
The properties thus determined shall meet all of the z265 test requirements for the base steel. Your comments are invited either for revision of this standard or for additional standards and should be addressed to ASTM International Headquarters. The base metal shall conform to the chemical requirements of the speci?