DIN EN Cable networks for television signals, sound signals and interactive services – Part 9: Interfaces for CATV/SMATV headends. Buy CEI EN CABLE NETWORKS FOR TELEVISION SIGNALS, SOUND SIGNALS AND INTERACTIVE SERVICES – PART 9: INTERFACES FOR . BS EN Cable networks for television signals, sound signals and interactive services – Interfaces for CATV/SMATV headends and similar.
|Country:||Antigua & Barbuda|
|Published (Last):||22 May 2009|
|PDF File Size:||7.97 Mb|
|ePub File Size:||6.85 Mb|
|Price:||Free* [*Free Regsitration Required]|
It is through the disparity characteristics of the code that DC balance is maintained. All parameters shall be met over the temperature, voltage, and lifetime range of the system. In addition references are made to all other parts of EN series Cable networks for television signals, sound signals and interactive services and in particular for RF, een and audio interfaces to part 5: Their committees work with the manufacturing and service industries, government, businesses and consumers to facilitate the production of British, European and International standards.
EVS-EN – Estonian Centre for Standardisation
The synchronous parallel interface is specified to cover short or medium distances, i. Need more than one copy? All signals are synchronous to the clock signal. The receiver buffer size, which is required to properly receive the data stream when the transmit and receive rates are linked, should be specified.
The abstract ASI delivery model is used to make sure that the isochronous output stream from the receiver buffer is similar to the isochronous input stream to the variable delay function. We have no document history for this standard. As measured according to the diagramme in Figure B. The extent of this standardization work is from the antennas, special signal source inputs to the headend or other interface points to the network up to the system outlet or the terminal input, where no system outlet exists.
Please first log in with a 500883-9 email before subscribing to alerts. The receiver shall present a properly aligned byte stream after the receipt of two K The packet synchronization process is not a part of this ASI Transmission protocol definition. Electrical characteristics The parameters shall be 500083-9 over the temperature, voltage and lifetime range of the system.
Optionally the RS coded bytestructure as specified in EN is also supported. In order to recover byte alignment, a decoder searches in the serial stream for the synchronization word which is necessary to achieve the serial to parallel conversion. Because the link and the TS are synchronous, the bit justification operation is not needed. This displacement can occur for a variety of reasons, e. The following dates were fixed: The packet length and the existence of valid RS bytes are conveyed through suitable coding mechanisms.
Of course, MPEG clock timing constraints are also assumed. It is constantly high in the byte mode. A phase-locked byte clock is derived from this recovered serial bit clock and is used to shift parallel bytes out to Layer-1 processing elements.
Recovered serial data bits are passed to a decoder which converts the bit transmission words back into the 8-bit bytes originally transmitted.
BS EN 50083-9:2002
The line driver and receiver shall be LVDS-compatible, i. All kinds of networks like: RD at the end of any sub-block is positive, if the sub-block contains more ones than zeros, or if the sub-block is or NOTE 4 For the purpose of these masks, the rise time and delay time 500883-9 be measured between —0,4 V and 0,4 V, and should not exceed 4 ns. Therefore, to ensure correct operation, care must be taken that equipment interface circuitry of the non-inverting type is used.
As the voice of the U. You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server.
The serial signal is Biphase Mark encoded. Otherwise the last RD is taken. Some of these parameters may not be applicable to certain types of equipment. The nominal zero level for both masks should be aligned with the oscilloscope trace with no input signal. This website is best viewed with browser version of up to Microsoft Internet Explorer dn or Firefox 3.
While the Fibre-Channel FC supports single mode fibre, multi-mode fibre, coaxial cable and twisted pair media interfaces, this standard defines only two distinct forms of interfaces: The cable shall have a coaxial pair shall be assumed to follow an approximate maximum insertion loss of 12 dB at a frequency of 70 MHz.
The SSI is based on a line rate directly locked to the transport rate. The relevant associated packet structures are illustrated in Figures 3 and 4. One can see that the buffer occasionally underflows. Active wideband equipment for coaxial cable networks EN Part 4: Which packet sizes are mandatory and which are optional is specified in Table 1.
The first curve shows this rate converging to 10 kHz after about samples 0,07 s.
Byte synchronization The byte alignment synchronization pattern shall be the K The variable ACCTn is the 500839 in the loop filter, and it converges to the time interval between arriving sync bytes. Cabled distribution systems for television and sound signals. A detailed specification of the SSI is provided in annex A and guidelines for its implementation are provided in annex D.