LM R e Thin Film Resistor Network. 0 05% Matching and 5 ppm This datasheet has been download from: Datasheets for electronics components. On all operational amplifier data sheets, the specifications listed on the deep in the data sheet. .. , LM and LT with improved price/performance. LM Datasheet: LM Precision Operational Amplifier, LM PDF Download National ->Texas Instruments, LM Datasheet PDF, Pinouts, Data Sheet.

Author: Gagal Maktilar
Country: Mauritius
Language: English (Spanish)
Genre: Software
Published (Last): 9 August 2018
Pages: 302
PDF File Size: 4.73 Mb
ePub File Size: 12.28 Mb
ISBN: 755-2-42692-969-2
Downloads: 11562
Price: Free* [*Free Regsitration Required]
Uploader: Zuluzilkree

In Sinking mode, connect 0. These pins may l6m07 cut xatasheet if desired. Capacitance in the Typical Performance Characteristics section show graphically that a modest capacitance of 0. The device does not include a thermal shut-down circuit.

The LM also provides excellent stability vs. The output can sink current as well as source it, but the output impedance is much better for sourcing current. The devices have a Dtasheet output has a class-B stage, so if the load current changes from sourcing to sinking, an output transient will occur. To avoid this transient, it may be advisable to preload the output with a few milliamperes of load to ground. The trim pin pin 5 should also be guarded away from noise signals and leakages, as it has a sensitivity of 15 millivolts of DVout per microampere.

(Datasheet) LM pdf – Precision Operational Amplifier (1-page)

The LM is suitable for limited-temperature operation. This datasheet has been downloaded from: National Semiconductor Europe Fax: Tsimshatsui, Kowloon Hong Kong Tel: The LM is recommended for applications where the highest stability and lowest noise is required over the full military temperature range.

In some applications it may datasheeet advantageous to pre-load the output to either Vin or to ground, to avoid this crossover point. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur.

Consult factory for availability of devices with Guaranteed Long-term Stability. For example, if the output were trimmed up to They are based on a buried zener reference as lm67 in the LM references, but do not require any heater, as they rely on special temperature-compensation techniques Patent Pending.


Consult factory for availability of devices with tighter Accuracy and Tempco Specifications. Documents Flashcards Grammar checker.

Avoid such overloads for voltages datashheet than a 20 V, for more than 5 seconds, or, at high ambient temperatures.

(PDF) LM Datasheet PDF Download – Precision Operational Amplifier

A military RETS electrical test specification is available on request. Pin numbers for H, M or N packages. If the output is pulled to a positive voltage such as a 15 or a 20V, the output current will be limited, but overheating may occur. The capacitor used should be a low-leakage type. These pins would not be damaged by a short to ground, or by Electrostatic Discharges; however, keep them away from large transients or AC signals, as stray capacitance could couple noises into the output.

Do not connect anything to these pins, or improper operation may result. The trim scheme is such that individual resistors are cut open rather than being trimmed partially cutto avoid resistor drift caused by electromigration in the trimmed area. The curves showing the Noise vs. The output is short-circuit-proof to ground. Its long-term stability is typically 3 to 10 ppm per hours when held near Tmax, and slightly better when operated at room temperature.

Thermal regulation is defined as the change in the output voltage at a time T after a step change of power dissipation of mW. These limits are not to be used to calculate outgoing quality levels.

LM607 View Datasheet(PDF) – National ->Texas Instruments

Alternatively, a shield foil can be laid out on the printed circuit board, surrounding these pins and pin 5, and this guard foil can be connected to ground or to Vout, effectively acting as a guard against AC coupling and DC leakages. LM see curve above: Life support devices or systems are devices or systems which, a are intended for surgical implant into the body, or b support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user.


The LM has a Class B output, and will exhibit transients at the crossover point. However, avoid overloads at high ambient temperatures, as a prolonged short-circuit may cause the junction temperature to exceed the Absolute Maximum Temperature. Trimming to a wider range is possible, but is not recommended as it may degrade the Tempco and the Tempco linearity at temperature extremes. Ceramic capacitors may seem to do the job, but are not recommended for production use, lm60 the high-K ceramics cannot be guaranteed for low leakage, and may exhibit piezo-electric effects, converting vibration or mechanical stress into excessive electrical noise.

A critical component lm067 any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. There is no guarantee that the Specified Temperatures are exactly at the minimum or maximum deviation. Contact the factory for availability of devices with proven long-term stability. A trim pin is available which permits fine-trimming of Vout, and also permits filtering to greatly decrease the output noise by adding a small capacitor 0.

This point occurs when the device is required to sink approximately 1. Changes in output voltage due to heating effects are covered under the specifications for Thermal Regulation and Datadheet. Regulation is measured at constant temperature using pulse testing with a low duty cycle. Unless otherwise noted, these conditions apply: